Okay first off lemme start by saying that my xbox 360 didn’t get the RROD from heat. It was more then likely a static discharge… if you don’t know what it is don’t worry about it… Tools for RROD Repair forums.xbox-scene.com 8 Machine Screws 16 Metal/Zinc Plated Washer 16 Nylon Washers [Video contains Home depot parts, and link contains lowes parts] ~Tools~ Multiple size flat head screwdrivers XCM Xbox 360 Opening tool Torx T8 & T10 screws/ bits Artic Silver 5 Thermal Compound Achool to …
where can i buy those fans can someone tell me how they are called i know they are no the whispermax fans please someone tell me how they are called
where can i buy those fans please someone tell me
my xbox fans are dead i think they dont start at all , when i start it , and my xbox is even cleaner then this piece of shit
yes, insult the video maker, while asking for help.
overheating
ok sorry i dont know why i said that lol this xbox is way better then MY piece if shit ,that was what i ment, i think
Mainly those are moded fans or they could sell them at llama (DOT) com
it’s overheating, but if it goes right away into the 2 rings right after start, then it’s a RAM problem. Basically one of the two RAM chips under the heatsink lost a connection with the motherboard, the only way you can fix it now is by reflowing the solder connections with a heat gun. It’s very risky but it works, I had the same problem and the heat gun fix worked for me. It was a last resort for me because I was about to throw my 360 against a wall after trying everything to fix it!
you can get the silver arctic at radioshack its like ten bucks and well worth it.
what sized machine screws would be helpful
I was always told that if you have a ESD (electronic static discharge) your circuit and chips on the board will get permanently damaged and its beyond repair.
You did not get a RROD from a static discharge or you wouldn’t have been able to repair it with a fix.
dude i love the song!
ok lets just show off my gay fan for the first minute of the video
ok im on the thermal compound part and
2 things
1. have you incountered any freezing and how long has i been
2. can you use household products to clean your chip cause my mom wont get me anything to clean it cause schools starting again and shesays i playi it too much
like wtf right im 17 let me entertain myself
lol thats beat dude…you can use regular rubbing alcohol on a quetip.should clean it up real nice ^^
cool thanks
hey uhmm..is dere any household chemical thing dat acts like artic silver??..cuz i need sumthing 2 cover da chips nd i aiint go shyt !
i just used goo gone and it was clean in like 2 seconds, but after you use it make sure you get a slightly damp kleenex and wipe it, then dry it with another piece of kleenex as the goo gone will leave an oily surface.
no,no,no im talking bout wat can i apply 2 da chips dat can act as or like arctic silver paste..i already removed dat gooy shyt my chips are sparlky clean..wat i gotta do is put sumthing over iht..i tryed black tape nd iht almost worked..4rm 3 rings i had 2
oh sorry my bad, umm i just went to radio shack and got a tube of thermal heat paste, the brand was nexxtech i think, just ask a clerk its like 5 bucks tops. but a very small amount on the chips and spread it over the chip. make sure you dont put to much on or it will just smuther the chip and over heat almost instantly.
nope dont try nothin stupid n put toothpaste or some shit on there lol. Jus buy arctic silver from amazon for bout £5.00.
thinner is prob the best to clean off the old compound or goo and wont damage the board! you can use alcohol after if desired with q-tip. if you have a small paint brush or (acid brush) that would work well with cleaning!
I used 99% isopropanol alcohol and it seems to work fine. My xbox keeps burning out though. This is the 3rd time in less than 2 months I’ve had to redo it.
im about to open and try my first one tommorow morning and see what it all looks like up close but the cold solder on the micros seems to be the biggest problem! this looks to be a solder pad ic and not the traditional pin chip! the heat gun would prob be the best bet since the unit is not powered on and the micro is not burning itself out decreasing longevity! using a heat gun will prob give you the longest results IMO. i will update when finished with results.